The bucket elevator has the advantages of large conveying capacity, high lifting height, stable and reliable operation and long service life. Its main performance and parameters are in line with JB3926----85 "Vertical Bucket Elevator" (the standard is equivalent to the international standard) And foreign advanced standards), the traction ring chain is in line with MT36----80 "mineral high-strength circular chain", this hoist is suitable for conveying powder, granular and small block without wear and abrasion. Small materials such as coal, cement, stones, sand, clay, ore, etc., because the traction mechanism of the hoist is a circular chain, it is allowed to transport materials with higher temperature (material temperature does not exceed 250 °C). The general conveying height can be up to 40 meters. The TG type can be up to 80 meters. The bucket elevator is suitable for lifting from a low place to a high place. After the material is supplied to the hopper through the vibrating table, the machine automatically runs continuously upwards. According to the transmission amount, the transmission speed can be adjusted, and the lifting height can be selected as needed. The hopper is designed and manufactured by itself. The PP non-toxic hopper makes the bucket elevator more widely used. All the dimensions are designed and manufactured according to actual needs, and it is suitable for vertical packaging. Machine, computer measuring machine design, suitable for food, medicine, chemical industrial products, screws, nuts and other products to enhance the loading, can control the automatic stop of the machine through the signal recognition of the packaging machine. The bucket elevator is a continuous conveying machine that vertically lifts materials by using a series of hoppers that are uniformly fixed to the endless traction members. Divided into three kinds of chain, plate chain and belt. Working principle: The hopper picks up the material from the storage below, as the conveyor belt or chain is lifted to the top, bypassing the top wheel and then turning down, the bucket elevator pours the material into the receiving tank. The belt of the belt-operated bucket elevator is generally a rubber belt that is mounted on the lower or upper drive roller and the upper and lower redirecting rollers. The chain drive bucket elevator is generally equipped with two parallel drive chains with a pair of drive sprockets on the upper or lower side and a pair of reversing sprockets on the bottom or the top. Bucket elevators are generally equipped with organic shells to prevent dust from flying in the bucket elevator. Bucket elevator: It is suitable for lifting from low places to high places. After the materials are supplied to the hopper through the vibrating table, the machine automatically runs continuously upwards. Main component bucket elevator consists of housing, traction (conveyor chain), hopper, drive wheel (head wheel), reversing wheel (tail wheel), tensioning device, guiding device, feeding port (inlet) and unloading Feed port (discharge port). Hopper a. Cylindrical bucket: deep bucket, bucket mouth is inclined at 65o, large depth, used for drying, good fluidity, goodly transported granular material. Shallow hopper: The mouth is inclined at 45o and has a small depth for wet and fluid granular materials. [Deep hopper: deep bucket general material is relatively dry and fluid. 】 [Triangle hopper: the material is generally directed self-flow discharge. 】 b, sharp-angled bucket: the side wall extends to the outside of the bottom plate, which becomes the rib. When unloading, the material can be unloaded along the groove formed by the rib of the bucket and the bottom plate, suitable for thick and heavy blocks. Material delivery. Traction member (a) Rubber belt: It is fixed to the belt mouth with screws and elastic gaskets. The belt is 35~40mm wider than the bucket. Generally, the tape conveying temperature does not exceed 60°C. The heat-resistant tape can transport materials up to 150°C. (b) Chain: The single chain is fixed to the rear wall of the hopper; the double chain is connected to both sides of the hopper. The chain hoist adopts a single chain when the hopper width is 160-250mm, and double-chain when the hopper is 320-630mm. The main disadvantage is that the chain between the links is worn and the number of inspections is increased. Sprocket The drive sprocket on the bucket elevator. The sprocket is intended to engage the pitch link or the pitch-accurate block on the cable. It is a solid or spoke-shaped gear that meshes with the roller chain to transmit motion. The design of the tooth shape of the sprocket: the sprocket tooth shape must ensure that the chain energy-saving smoothly enters and exits the meshing, minimizes the impact and contact stress of the chain link during meshing, and is easy to process. The sprocket material should ensure that the teeth have sufficient strength and wear resistance, so the sprocket tooth surface is generally heat treated to achieve a certain hardness. Main features 1. Low driving power, using inflow feeding, inducing unloading, and large-capacity hopper intensive arrangement. There is almost no returning and excavation during material lifting, so there is less reactive power. 2. Wide range of lifting, this kind of hoist has less requirements on the type and characteristics of materials, not only can improve the general powdery and small granular materials, but also can improve the material with high abrasion resistance. It has good sealing performance and less environmental pollution. 3. The operation reliability is good, the advanced design principle and processing method ensure the reliability of the whole machine operation, and the trouble-free time exceeds 20,000 hours. The lifting height is high. The hoist runs smoothly, so it can reach a higher lifting height. 4. The service life is long, the feeding of the hoist adopts the inflow type, and there is no need to use the bucket to dig the material, and the extrusion and collision phenomenon rarely occur between the materials. The machine is designed to ensure that the material is less sprinkled during feeding and unloading, reducing mechanical wear.